How to Measure for a Fire Door

How Do You Measure for a Fire Door Step by Step?

Measure the opening at several points. Walls, floors and lintels can be uneven. Record each width and height and take the actual condition of the opening into account when determining manufacturing dimensions.

  1. Prepare the opening. Clear loose plaster, temporary profiles, foam residue and anything else that could affect the measurements.
  2. Measure the width at three points. Measure between the walls at the top, middle and bottom. Different readings indicate an uneven opening.
  3. Measure the height at least twice. Measure from the floor to the lintel on both sides. For a wide opening, also measure at the centre if needed.
  4. Measure the wall thickness. Check several points so the frame or trim can fit the wall correctly.
  5. Allow for the finished floor level. If screed, tile, stone or another finish is still to be installed, account for the final floor height.
  6. Confirm the opening direction. Record whether the door opens to the right or left based on the escape direction and intended use.
  7. Determine the number of leaves. Use the opening width and the required clear opening to determine whether one or two leaves are needed.
  8. Record the dimensions on a sketch. Show the width, height, wall thickness, opening direction and any fixed leaf.

A laser measure can be used. A tape measure and spirit level also help check corners, wall alignment and floor level. Record all dimensions in either centimetres or millimetres to avoid confusion when ordering.

The wall opening and the external frame dimensions are different. The manufacturer should specify the installation clearance based on the frame system and wall construction. Treat measurements taken on site as inputs to the manufacturing specification.

What Should You Check When Measuring for a Fire Door?

Consider the technical conditions at the installation site. Two openings with the same width and height may need different doors because of wall construction, floor level or escape requirements.

  • Measure at several points. A single reading can miss irregularities.
  • Check the narrowest point. Identify constrictions and projections that could prevent the frame from fitting.
  • Identify the wall type. Fixings and installation methods can differ between reinforced concrete, aerated concrete, brick and plasterboard.
  • Confirm the finished floor level. Measuring from an unfinished floor can result in an incorrect door height.
  • Check the required clear opening. The frame and open leaf reduce the available passage width.
  • Allow room for the panic bar and handle. Nearby walls, columns or services must not interfere with the hardware.
  • Check the closer location. Beams, low ceilings and services above the door can affect installation.
  • Keep the swing area clear. The leaf must not strike a wall, stair, railing or another door.
  • Check the technical documentation. Dimensions, glazing, louvres, leaf count and hardware must be within the scope of the selected system’s documentation.

In refurbishment projects, confirm whether the existing frame will be removed. Measuring inside an existing frame differs from measuring the structural opening. Fitting the new door inside that frame can further reduce the clear opening.

The opening direction matters as much as the dimensions. On an escape route, determine it based on the project’s occupancy and applicable requirements. When ordering, state whether the door opens to the right or left and identify the side from which it is viewed.

What Are Standard Fire Door Dimensions?

No single manufacturing size applies to every project. Dimensions depend on the building type, occupant numbers, escape route calculations, required clear opening, number of leaves and the technical scope of the selected system.

Manufacturers may offer models in common widths and heights. Whether these are suitable depends on the project, particularly in hospitals, schools, hotels, factories, warehouses and shopping centres.

Under Article 157 of Türkiye’s Regulation on Fire Protection of Buildings, escape route doors covered by the rules for existing buildings must be at least 70 cm wide and 190 cm high. These are minimum dimensions for the specified escape routes. Manufacturing dimensions and the requirements for new buildings or other uses must be assessed separately.

Measurement Description
Structural opening Width and height of the opening that will receive the frame.
External frame dimensions Overall width and height of the frame to be manufactured.
Leaf dimensions Width and height of the moving part of the door.
Clear opening Usable, unobstructed passage with the door open.
Wall thickness Depth of the wall that the frame or trim must fit.

Standard sizes generally refer to common manufacturing dimensions. Use the dimensions specified in the architectural plans that also meet safe escape needs. A door’s ability to fit the opening is only one part of assessing suitability.

For custom sizes, check the scope of the fire performance documentation. Dimensions outside the tested or assessed range do not automatically achieve the same performance. See Brango’s fire door page for sizes and product options.

What Are Frame, Leaf and Clear Opening Dimensions?

Record the structural opening, frame, leaf and clear opening separately. Confusing them can cause problems in manufacture and installation. Accurate clear opening dimensions are especially important on escape routes.

The structural opening is the width and height of the opening where the door will be installed. External frame dimensions are measured across the outside of the steel frame. Installation may require clearance between the frame and wall.

Leaf dimensions describe the width and height of the moving part. The leaf fits inside the frame and is smaller than the external frame dimensions. The clear opening is the actual unobstructed passage with the door fully open.

Measurement Meaning Why it matters
Structural opening The opening where the door will be installed. Allows the frame to be manufactured to fit the opening.
External frame dimensions Overall width and height of the steel frame. Used to determine installation clearance and fit against the wall.
Door leaf dimensions Dimensions of the moving part of the door. Affect how the door operates in the frame.
Clear opening dimensions The actual usable passage when the door is open. Important for assessing evacuation and passage capacity.
Wall thickness Depth of the wall where the door is installed. Helps select the correct frame and trim.

A 100 cm structural opening does not necessarily provide a 100 cm clear opening. Frame profiles, hinges and the open leaf can reduce the usable passage. Check the required clear opening before manufacture.

Confusing frame, leaf and clear opening dimensions can result in a door that does not fit, insufficient clear passage or extra building work. Identify each measurement on the order form.

How Do Dimensions Differ Between Fire Doors With One or Two Leaves?

Doors with one leaf suit narrower openings where a single leaf provides the required clear opening. Doors with two leaves may suit wider passages, heavy foot traffic or projects where large equipment needs to pass through.

For a door with one leaf, measure the opening width, height and wall thickness and confirm the opening direction. For a door with two leaves, also specify how the width will be divided between the active and inactive leaves.

  • One leaf. Opening the single moving leaf provides the clear passage.
  • Two leaves. The leaves can be manufactured in equal or unequal widths.
  • Active leaf. The main leaf used for daily access.
  • Inactive leaf. The second leaf opens when more passage width is needed.
  • Clear opening calculation. Assess the available passage separately with one leaf open and with both leaves open.
Feature Fire door with one leaf Fire door with two leaves
Number of leaves One Two
Application Standard or narrower openings Wide openings with frequent use
Dimension planning Based on one leaf and its frame The active and inactive leaves are specified separately.
Hardware planning A single closer or locking system may be used. A door coordinator and additional hardware may be needed.
Clear opening Based on the open position of the single leaf. Can be calculated separately with one or both leaves open.

The closing sequence matters for fire doors with two leaves. Suitable closers and a door coordinator may be needed to ensure the inactive and active leaves close in the correct order. Check that the hardware suits the door dimensions and is covered by the technical documentation.

When choosing one or two leaves, assess occupancy, the evacuation scenario, equipment access, the required clear opening and project requirements together with opening width.

What Problems Can Incorrect Fire Door Measurements Cause?

Incorrect measurements can complicate installation and affect operation, closing performance and project suitability. Cutting the frame, narrowing the door or making uncontrolled modifications can compromise the assembly.

Incorrect or incomplete measurements can lead to the following problems.

  • The frame does not fit the wall opening.
  • Excessive gaps remain between the frame and wall.
  • The leaf rubs against the floor or frame.
  • The door fails to close fully and automatically.
  • The clear width falls short of the project requirement.
  • The panic bar or handle strikes the wall.
  • The door closer cannot be installed.
  • The door is made to open in the wrong direction.
  • Additional demolition or alterations are needed during installation.
  • Fire and smoke seals fail to make proper contact.
  • The product falls outside the scope of its certification or technical documentation.
  • Manufacturing and delivery take longer.

An incorrect floor level can leave too much clearance under the door or cause the leaf to rub against the floor. If the finish has yet to be installed, calculate its thickness in advance.

Another common mistake is to treat the wall opening and external frame size as identical. The manufacturer should specify the required installation clearance based on the frame and installation method.

Before ordering, show the measurements on a sketch or plan and record the opening direction, number of leaves and wall thickness separately. On large projects, assign each door its own code to track manufacture and installation.

Brango offers fire doors with one or two leaves, panic bars and custom dimensions for different buildings and projects. Review dimensions, opening direction, hardware and project requirements together before manufacture.

Disclaimer. These measuring instructions provide general information. Final manufacturing dimensions can vary with the selected door system, architectural plans, clear opening requirements, technical documentation and installation conditions. Have qualified technical personnel verify the measurements before ordering.

×
Turkish English العربية
×
×
Contact Panel